Just How to Remove as Well as Replace a Tub
Just How to Remove as Well as Replace a Tub
Blog Article
Just how do you actually feel in relation to A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately tough job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This short article will certainly aid you mount a brand-new tub in your restroom if you have already gotten a brand-new tub as well as do not need to change the arrangement of your previous water supply pipelines.
Your devices and material list should consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather bothersome as a result of the limited gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making certain that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type should be connected to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub till the level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water system as well as check all joints as well as new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its last placement.
Getting ready for the Installation
To start with, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall surface between the bath as well as the tiling, causing issues with wetness and also possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can split rather very early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is advisable to fit the tiles using waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub? Make a remark down below. We'd be interested to hear your suggestions about this post. Hoping that you come back again later on. Make sure you take a moment to share this article if you enjoyed reading it. Thanks for going through it.
Information
Report this page